Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Bathroom Remodeling: The Fresno Owner’s Guide
A full PGT bathroom remodel in Fresno typically runs $9,000 to $28,000 installed, depending on whether you’re replacing a vanity or gutting the room to the studs and rebuilding the shower, floor, and fixtures. We carry PGT-compatible parts for remodeling work, and we can usually start the project within two to three weeks of your signed scope of work. Most Fresno homeowners discover they need this work when a vanity door hinge finally gives out, grout starts crumbling around the tub, or a shower valve seizes up after years of hard water from the city supply.
The picture most of our calls fit: a bathroom that works, more or less, and then one part fails in a way that makes daily life harder than it should be. The truth is, a failing part in a PGT bathroom rarely exists in isolation. The surrounding surfaces, the seal lines, the framing behind the tile, they have all been aging at the same rate. That is why we look at the whole fixture pull, the waterproofing layer, the valve body, not just the one broken piece.
Which PGT Models This Applies To
PGT bathrooms in Fresno homes come in two broad groups: original-spec installations from the builder, and retrofit jobs where a homeowner added PGT fixtures or cabinetry later. The original-spec group is the more common one we see in neighborhoods like Woodward Park and Sunnyside, where houses went up in the early 2000s and the PGT vanity sets, mirror frames, and tub surrounds are now twenty-plus years old.
Not every PGT-labeled part is interchangeable. Older PGT vanity cabinets used 35mm cup hinges with a specific overlay measurement, and newer lines moved to soft-close mechanisms with a different bore pattern. If you pull a hinge and see a stamped number on the inside of the cup, that number tells us the line and the year. If there is no stamp, we measure the overlay and the door thickness, then match to a current PGT-compatible hinge or a quality aftermarket equivalent that fits the same bore. For remodel work, we are less concerned with matching the exact PGT line and more concerned with whether the new part will carry the weight and daily use correctly.
We also remeasure shower valve rough-ins when PGT trim is being replaced. A PGT tub/shower valve from the mid-2000s often has a rough-in depth that does not play well with newer trim kits, so the valve body itself may need to come out. That is the kind of discovery that changes a $2,000 fixture refresh into a $4,500 valve replacement, and it is exactly why we put the scope in writing before work starts.
Styles & brands we work with
Signs Your PGT Bathroom Remodeling Is Failing
- Soft-close hinges no longer close softly. The damper inside the hinge cup has worn out. On a PGT vanity door that gets opened thirty times a day, those dampers last roughly eight to ten years in Fresno’s dry heat before they lose resistance.
- Grout lines along the tub or shower base stay dark after cleaning. Water is getting past the seal and sitting in the substrate. In Fresno’s hard-water environment, mineral buildup can mask this for months before the tile actually shifts.
- The shower valve drips when the handle is off, or the handle spins past its stop. The cartridge is worn, and on older PGT valves the replacement cartridge is often no longer manufactured. We then match a current valve that fits the existing plumbing rough-in, or we open the wall and replace the valve body.
- Drawers in the vanity stick at the same point every time. The drawer glide has a bent runner or a broken ball bearing. PGT drawer boxes from the original-spec era used side-mount glides that weaken with the repeated weight of toiletries and cleaning supplies.
- The mirror frame is pulling away from the wall or the glass is fogging at the edges. The adhesive or the mechanical fasteners have aged. In a Fresno bathroom subject to daily steam from showers, a failing mirror mount is a warning sign for moisture problems behind the drywall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Fresno, the installed price for a full PGT bathroom remodel lands between $9,000 and $28,000. A smaller job, like a vanity replacement with new PGT-compatible cabinetry and a Kohler faucet, sits in the $9,000 to $12,000 range. A full gut with a Schluter waterproofing system, new tub or walk-in shower, Cambria or Silestone counters, and Moen or Grohe fixtures moves toward the $22,000 to $28,000 end.
Here is how that breaks down on a typical mid-range Fresno bathroom remodel:
- Demolition and disposal: $900 – $2,200
- Plumbing rough-in and valve replacement: $1,500 – $4,000
- Waterproofing and tile work: $3,000 – $8,500
- Vanity, countertop, and fixtures: $2,500 – $8,000
- Flooring, trim, and paint: $1,100 – $3,500
Every line item is written down before we start, and the price does not change once the crew arrives unless you ask for a change. All work carries our 365-Day Done Right Promise: if something is not done right, we make it right. The brands we install, KraftMaid, Cambria, Silestone, Kohler, Moen, Grohe, carry manufacturer warranties that travel with the finished project.
DIY or Call Us?
Some PGT repair work is safe to check on your own. Tightening a loose hinge screw, replacing a showerhead, swapping a visible escutcheon plate, these are all within reach of a careful homeowner. If you can see the part clearly and no water or electrical lines are involved, go ahead.
The call-us line is drawn at anything inside the wall or behind the tile. A shower valve replacement that requires opening the wall is not a weekend job, and getting the waterproofing wrong behind a new PGT surround leads to mold you will not see until the tile starts moving. The same goes for any plumbing that touches the supply lines. If you are not certain, call (559) 540-8453 and ask. Graham Stein has been doing this work for going on twenty-six years, and we would rather answer a question than fix a rushed repair.
FAQs
Most PGT bathroom remodels in Fresno take two to four weeks from first demo to final clean-up, with the range depending on the size of the room and whether we are moving plumbing. A vanity swap can be done in three to five days. We keep the project calendar updated and tell you before the crew arrives each morning what the day looks like.
Yes, we repair what can be repaired, and we will not push a full remodel when a hinge replacement or a valve cartridge does the job. The honest issue is that on twenty-year-old PGT fixtures, repair parts are often discontinued, and the cost of a one-off match can approach the cost of a new fixture. We show you both numbers and let you decide.
We stock common PGT-compatible hinges, drawer glides, valve cartridges, and shower trim kits on our trucks, so a repair visit often finishes the same day. For remodel work, we order the specific pieces after the written scope is signed, and the lead time is usually one to two weeks.
No. The price you sign is the price you pay, unless you ask us to add something mid-project. If we find condition issues behind the tile that the original scope could not have predicted, we stop and talk to you before doing anything else. Write it down before anything comes off the truck.
If you have a PGT bathroom that needs work in Fresno, call (559) 540-8453 for a free estimate. We will come out, look at what you have, and give you a written price before anything begins.
Written by Graham Stein, Owner, Elmstead Remodeling Fresno at Elmstead Remodeling Fresno, serving Fresno and nearby areas.
